Skateboarding is no longer a strange sport to us. Skateboarding enthusiasts always want to show their class through the wheels.
Small wheels will not be able to satisfy that desire. They hinder your speed and technique. That’s why many people want to change the small skateboard wheels into long wheels. So, can you put longboard wheels on a skateboard?
- Can you put longboard wheels on a skateboard?
- How to put longboard wheels on a skateboard?
- Problems when playing skateboard with longboard wheels
- Measures to reduce the risk of injury when playing skateboard
- How to choose to buy components for a skateboard?
Can you put longboard wheels on a skateboard?
The answer is yes. But I’d advise you to exercise caution when performing this action.
The larger the skateboard wheel, the faster the speed will be. The wheel of a skateboard itself is usually 48 to 60mm in diameter and 63 to 75mm in length. You can completely replace them with longer cakes of larger diameter. In long distances, longboard wheels will help you control more easily and avoid collisions.
When performing the techniques, it takes less force to perform than with conventional wheels. However, to avoid bites, you can place longboard wheels on the skateboard but they should not be larger than 70mm.
Depending upon your weight, you must tighten your truck with 1/2 spacers and 1/2 bolts. You should also prepare stiff bushings to avoid biting the wheel.
You can place longboard wheels on the skateboard but they should not be larger than 70mm
How to put longboard wheels on a skateboard?
Many people think that it is impossible to put a longboard wheel on a skateboard. They were indeed wrong. On the other hand, mounting a longboard wheel is not as difficult as you might think. We will guide you in detail on how to do it. To do this, you need to prepare some tools as follows:
- Skate tool
- 4 longboard wheels of diameter not exceeding 70mm.
- 8 1½ bolts
- 2 riser pads
Step 1: Remove the old wheel of the skateboard
You use bolts and screwdrivers to unscrew the wheel screws. You will have to use a lot of force to remove it. This is the place to be sure.
Otherwise, you will fall very violently. The distance between the deck wheels is not much space. You need more space to make it easier and safer.
Step 2: Install the Riser gasket
Prepare long bolts and thick spacers. Shorter bolts will not be able to securely attach the Riser gasket. You need the fabric to attach the Riser spacer to the center where the trucks attach to the board. The ground clearance with the skateboard is 58mm. As such, the new riser gasket works at its best.
You can choose the size of the longboard wheel, but make sure your truck can handle it. Make sure they are properly positioned and sturdy to ensure safety for long trips. The compatibility and performance of the gasket is the most important factor.
The ground clearance with the skateboard is 58mm for the best performance of the riser pad
Step 3: Install the longboard wheel on the skateboards
Before proceeding to install the longboard wheel, you need to make some adjustments. The wheel will bite your board if the truck is not adjusted.
In order for the wheel to be firmly fixed, you must adjust the forklift truck to a certain distance. In addition, you also have to adjust the pads to make them more effective during operation.
Surely you will be new to the new longboard wheels. You will lose stability as the distance between the ground and your feet is raised. Please do not perform the techniques because you may encounter injuries.
You should adjust gravity by bending lower to lower the center of gravity. Collisions between wheels and deck may occur. This will precarious your plank. Get used to this innovation slowly for safe rides.
Problems when playing skateboard with longboard wheels
Skateboarding has a high frequency of injuries. While Skateboard has a lot of jumps, Longboard with smoothness is stable even at fast speeds.
Skateboarding with longboard wheels will be a combination of them. It will cause problems you cannot foresee. We will give a breakdown when you skateboard like this.
Cruising is quite safe and few skaters have an accident while playing. But sometimes, you also run the risk of falling off your skateboard when you hit an obstacle. You will often be injured in places such as knees and elbows while cruising.
This is a style of play that favors the technique of the feet and the speed of the slide. Therefore, players are often at risk of muscle and ligament injuries. In addition, sprains and strains around the feet and ankles are possible.
This is quite a dangerous game because skaters often slide at high speed. They often fall easily when sliding. There is even a risk of collision due to high speed.
Downhill is almost the most dangerous type of play because the sliding speed is extremely fast. But that’s why Downhill believers are always aware of safety issues. They must wear full protection when playing. This greatly reduces the risk of injury.
Measures to reduce the risk of injury when playing skateboard
No matter how careful you are, accidents are sometimes inevitable. So take the following measures to minimize the risk of injury.
You may not like wearing a helmet, but it will help you avoid a lot of injuries. Helmets, elbow pads, and pillowcases are basic tools. Instead of trying to look cool, wear protective gear to ensure your own safety.
Do not use alcohol or drugs. Whether you’re driving or skateboarding, don’t use alcohol or drugs. They will impair concentration and can cause serious accidents.
Thoroughly inspect the skateboard before playing. Because the skateboard can have a few problems in its parts. Always pay attention to obstacles on the road and control the speed. If possible, choose slides that are safe, flat, and low in obstacles and traffic. Do not forget to get enough sleep and do not skate when in poor health.
You must always stay focused when playing skateboard
However, if you accidentally collide with vehicles on the road, stay calm and do not move. You need to avoid aggravating the injury. Call an ambulance immediately and signal for help from around if needed.
How to choose to buy components for a skateboard?
Currently, the market offers you a variety of skateboard products. Most of them have been carefully selected and checked for quality.
The variety of longboards also makes it difficult for many people to choose. We will provide the necessary knowledge to help you make the right choices. If you are looking to upgrade your board, we hope this knowledge will help you.
Choose a pre-assembled skateboard
To save time, you should not choose each part to assemble. You can choose from pre-assembled skateboards. These include beginner sets and high-quality sets. Especially for those of you who want to invest in high-intensity track practice.
Self-select each component to assemble
A complete set of longboards including Deck, Trucks, Wheels, Bearing, Griptape, and Hardware. The size of the deck is the width of the board in inches. The size and length of the deck will have their own customizations. But for the most part, there was no significant difference in each brand.
Try skating on different sizes of boards to feel the difference. This will help you find the longboard size that works best for you. There are no scientific guidelines for deck size selection. Each person’s deck size depends on their preferences and experience.
Trucks are T-shaped metal parts mounted underneath the Deck. The size of the trucks is equal to the length of the crossbar. The rubber part, kingpin, pivot, and screw can be replaced when they are damaged.
When buying trucks, you need to pay attention to choosing the size trucks that match the size of the deck. This means that the length of the Axle bar is equal to the width of the board.
Most skateboard wheels are made of durable urethane material. When choosing wheels you need to pay attention to parameters such as weight, size, hardness… Wheels with large sizes will go faster. It also increases the height of the board to the ground.
With small wheels, the plank will be closer to the ground. Plank run is reduced and board control is better. Technical players often choose small, lightweight wheels to make trick flips easier. Large wheels for many speeds will be convenient for skateparks, ramps,…
You should start with a small wheel about 50mm to 52mm in size to make it easier to get used to the longboard
Griptape is used to stick on the board. It creates a grip between the shoe and the board. The sandpaper will make it easier for you to slide the board in the air. The increased friction makes it easier to flip the board.
Griptape each brand has a different roughness. Various textures make your board more beautiful and free to express your personality. The masters of grip tape making are Jessup and MOB.
Can I put longboard wheels on my skateboard for cruising? Now you have the answer for yourself. Do it yourself according to our guide for a new experience. We hope that this information will help skateboard enthusiasts like you.